As far as i am aware from my own setup, the shift light stages remain on even when others are activated.
You could also use engine speed controlled outputs A & B? If they arent already used.
Or spare Fan On/Off?
Graeme
Search found 70 matches
- Mon Apr 25, 2022 4:50 pm
- Forum: General Syvecs Chat
- Topic: resonance flaps: change light or configurable map?
- Replies: 3
- Views: 9627
- Sun Apr 03, 2022 8:14 pm
- Forum: General Syvecs Chat
- Topic: Any possibility of Real Dash support?
- Replies: 30
- Views: 53256
Re: Any possibility of Real Dash support?
Hey Any updated info or xml file etc on this? Anything to get this setup pain free would be ideal. I literally just bought the can to usb as i already have an in car pc (just an intel i5, 8gb ram, 128gb ssd) for audio and to use smon sdata etc while driving, but tired of the syvecs smon look haha Al...
- Fri Dec 17, 2021 11:43 pm
- Forum: General Syvecs Chat
- Topic: Syvecs Ultimate Customer support ! (Story)
- Replies: 3
- Views: 10717
Re: Syvecs Ultimate Customer support ! (Story)
I have had the S6GP for 5 years now, and considering this one time.purchase (I'd buy and build more if I had the money believe me) the support I have had off Ryan (who had always tuned my car previously also) has been second to none
Syvecs really is an amazing outfit
Graeme
Syvecs really is an amazing outfit
Graeme
- Thu Nov 18, 2021 7:41 pm
- Forum: General Syvecs Chat
- Topic: S6 Plus EGT fault
- Replies: 3
- Views: 3913
Re: S6 Plus EGT fault
Sounds like you connected the new sensors up reverse polarity, they read opposite so it would show the temp reducing
Graeme
Graeme
- Sat Oct 23, 2021 11:45 pm
- Forum: S7-I / S7Plus Technical
- Topic: Blip to rev match
- Replies: 4
- Views: 7236
Re: Blip to rev match
On my h pattern I use a brake switch and a clutch switch at the bottom of the clutch pedal, when both are depressed it gives a blip request (input as gear blip direct into ecu but I use a canbus circuit board to save inputs) Then in gear blip settings you can select how much the throttle opens and f...
- Sat Oct 23, 2021 11:39 pm
- Forum: S6-I / S6Plus Technical
- Topic: S6 Firmware
- Replies: 4
- Views: 13116
Re: S6 Firmware
It is a shame that there will be no updates, I have a couple of issues which are not the end of the world and I can work around them, but still it would be nice, like unlocking the canbus generic recieve haha
- Thu Apr 15, 2021 4:01 pm
- Forum: General Syvecs Chat
- Topic: Crank and Cam Trigger Sync on LS7
- Replies: 9
- Views: 9559
Re: Crank and Cam Trigger Sync on LS7
Put the wheel sensor into the old crank sensor location
Graeme
Graeme
- Fri Oct 02, 2020 9:21 pm
- Forum: Technical Deposit
- Topic: Power Steering Pressure Input for Idle duty adder
- Replies: 4
- Views: 21079
Re: Power Steering Pressure Input for Idle duty adder
Well if you have a spare input you can install a pressure sensor and use it as a custom sensor, then create a custom map based on that input (and another like tps etc if you want a 3d map) to add idle duty I know the battery one seems like it would have a delay, but it actually works great, I don't ...
- Mon Jun 08, 2020 11:48 pm
- Forum: Technical Deposit
- Topic: Power Steering Pressure Input for Idle duty adder
- Replies: 4
- Views: 21079
Re: Power Steering Pressure Input for Idle duty adder
Just seen this and it's an issue I have also, sometimes when stationary with my fans and fuel pumps running the car would bog and cut out as I turned the wheel. Also sometimes when fans kicked in, at night moreso with lights etc I made a custom table to increasing add idle duty against baterry volta...
- Sat Jun 06, 2020 11:37 am
- Forum: General Syvecs Chat
- Topic: More water / meth injection
- Replies: 99
- Views: 2978637
Re: More water / meth injection
Yeh I know mate, I was just being funny because there are no more firmware updates haha